Posts Tagged ‘V-LEDS’

If your are looking to upgrade your vehicles 3157 or 7443 parking light, turn signal, or brake light bulbs with V-LEDS you NEED to identify what TYPE of SOCKET your car has. There are 2 socket types, Standard and CK. There is only one way to know for sure which socket your car has, TEST IT. We put together a short video that will guide you through the steps involved with testing your sockets.

What is the difference between the Standard and CK style sockets? The position of the ground contacts in the socket is the only difference. They LOOK identical. What will happen if I use the wrong type of LED, i.e. A standard LED in a CK socket?  The LEDs will not work properly or worse, they will blow your fuses that protect that specific lighting circuit. How do I know which socket type I have? Watch the video below and follow the instructions.

There is no rhyme or reason as to what car will use a CK socket configuration. Again the only way to know is by following our testing procedure shown in the above video.

Please note: Single element sockets i.e. 3156 and 7440 can be CK style as well. Please test and identify your sockets BEFORE you purchase your new V-LEDS. There is a 15% restocking fee for returned products.

V-LEDS strip lights are a great way to add lights to the interior or exterior of your car or truck. The possibilities are endless for location and functionality of these style of LEDs. We have added another LED strip light to our already popular lineup. These LEDs are not the standard V-LEDS strip lights though. The first major difference you will notice about these strips is the LEDs are aimed to the side, not straight up like our standard strip lights. Second, these strip lights feature dual color, White and Amber LEDs wired separately on the same circuit board. These dual color strip lights function the same as our popular switchback LEDs. A simple 3 wire installation makes them easy to install in any car or truck.

V-LEDS Dual Color Switchback LED Strip Light.

Want to see more pictures of these lights installed on the V-LEDS Project Scion iQ? Click here and see the photo gallery.

The 3rd addition of V-LEDS to the 2011 Scion iQ is Footwell lighting. This car is small, very small. So it is equipped with a proportionately small dome light. It does not provide much light at all. We offer many different LEDs that replace the yellow filament bulbs in your car, but sometimes you need some extra light to see. What if your car does not have enough factory lights? This is where V-LEDS can make a huge difference on any car. We offer a wide range of strip lights that are suitable for just about any application you can think of.

For the V-LEDS Scion iQ we wanted to be able to see the interior when the door was open or when we unlock it with the keyless entry system. So we chose to use some of our new puck strip lights. These are available in multiple colors, we chose to use the 6K white  version. We used one per side, adhered to the bottom side of the dash with the double sided tape that comes on them. We wired these directly to the dome light circuit.

Puck Light mounted to drivers side under dash.

After routing the wiring and making the connections to the factory dome light wires it was time to test. The results are amazing!

So much light!

Onto the trunk area now. There is no light in the rear from the factory. So while we were wiring up the puck lights up front we used a Y adapter and ran some extensions to the rear of the car. There is a great location on the panel in the trunk area to mount a strip light. We used a 12″ piece of our STRIP_3C_W_6K to illuminate the cargo area.

Behold the power of V-LEDS!

Thats it for this installment of the V-LEDS project Scion iQ. Stay tuned for more updates as we continue to bring the light.

Here is a list of the products we used for this upgrade:

Puck Lights: STRIP_RL_12_W_6K

Strip Light: STRIP_3C_W_6K (select length)

Y Adapters: DIY2_Y_ADAPT

Wire Extensions: DIY2_WIRE_48 (there are shorter lengths of wire available here)

Thanks for reading. If you have questions regarding this product please send an email to our customer service department at sales@v-leds.com. We are quick to respond via email and can answer any questions you may have about our products.

Here are some more photos of our Scion iQ.

We are on the second lighting mod on our Scion iQ. On the rear bumper there are 2 circular reflectors. They looked a little out of place but are required by DOT for visibility. We looked at them and thought “these would be great if they were active”. So we decided to see if they could be dissected and turned into brake lights.

Here we see the reflectors with as they appear from the factory.

We started by accessing the back of the reflector. This was pretty easy, with the removal of few plastic snaps we were able to remove the small rear inner fender liner. This allowed easy access to the fastener that holds the reflector to the bumper. After removing the nut from the backside of the reflector it comes right out.

Behind the bumper you can see how the reflector mounts. You can also see the wiring for the LEDs.

The red reflector portion of this unit is plastic welded to the mount (backer). There is enough space inside to hold one V-LEDS STRIP_RL_12_R. To separate the red reflector from the backer we heated a razor knife and pressed it into the seam where the front and back are fused together. Then it was just a matter of wedging a small flat blade screw driver into the melted section and prying them apart. It is not a clean split, but is the most non-invasive way to get it apart so that they can be glued back together later.

After you separate the front and back its time to get them ready for the STRIP_RL_12_R to be installed. I oriented the LED disc so the pattern of LEDs was aligned so the vertically/horizontally. From there I drilled a hole for the wire to be routed through. I drilled a hole in the bumper so the wire could be routed through as well.

LED Installed Inside Rear Reflector.

Here are the reflectors after completion.

After affixing the LED we used super glue to reattach the reflector to the backer. It was a tight squeeze but it fit inside. After the glue cured we reinstalled them and routed the wiring through a factory rubber grommet located on the back of the car. We ran the wiring up to the factory brake lights and spliced it into the brake circuit.

Reflectors are now active brake lights.

Here is a list of all the components used on this upgrade:

2 of these: STRIP_RL_12_R

2 of these: DIY2_WIRE_48

1 of these: DIY2_Y_ADAPT

Thanks for reading. If you have questions regarding this product please send an email to our customer service department at sales@v-leds.com. We are quick to respond via email and can answer any questions you may have about our products.

Here are some more photos of our Scion iQ.

V-LEDS Platinum Edition High Power 20

Here at V-LEDS we pride ourselves on developing the latest in cutting edge LED technology for your car. The latest addition to our extensive assortment of LEDs is the Platinum Series High Power 20. This bulb features years of development and testing brought together to form the perfect combination of light output and aesthetic appeal. This V-LEDS product is overbuilt to deal with the most demanding of applications. From Daytime Running Lights to Brake lights, this LED can do it without problems. Thick aluminum circuit boards and a large machined heat-sink located at the top of the LED quickly dissipate the heat generated by the .5 watt diodes. Clear lenses with vent slots add to the finished look of the bulb. Each .5 watt diode, 20 total, make for an intense blast of light aimed directly into your cars reflective lenses for the brightest output available on the market today.

The Evolution Of The High Power 20 Bulb

The Design of the High Power 20 LED bulbs started years ago. There was missing product in the 7440/7443 category. Everything we tried was just not bright enough. We needed to do something completely different to achieve acceptable levels of light output. After designing different prototypes a decision was made to use different diodes. The .5 watt diode was realized as the best candidate for the job. These diodes pack a serious punch. Each .5 watt diode has the same light output of 10 of our standard diodes. They also create 10 times more heat than the standard diodes. Heat is an LEDs worst enemy and we needed to develop a means to dissipate the large amounts of  heat generated by these new diodes. This led to another technological innovation by V-LEDS, the aluminum circuit board. This allowed the full power use of the .5 watt diode in brake light applications. This technology is applied to all High Power .5 watt LEDs offered by V-LEDS. The first edition of the High Power 20 used 14 .5 watt diodes on the sides and 6 of our standard 1210 diodes on the top. This design was hugely popular, so popular in fact that we continued development all the way up to the current Platinum Series. As we continued to advance this product we knew it needed to be brighter and even more capable of dissipating the heat of the .5 watt diodes. The 3rd Generation of this LED was equipped with massive aluminum circuit boards to handle the increased power output of the LEDs. The 6 standard 1210 diodes on the top were replaced with 4 .5 watt diodes to get as much light output as possible. This bulb packed a serious punch, but the finished look of the bulb left something to be desired. Which is where the Platinum Series steps in. A few tweaks in diode placement and heat management combined with its vented lens and voilà. Stay tuned in to V-LEDS to see where we take this already amazing product. Can we make it any better than it is now? That was the same question we asked ourselves a few years ago and the answer is YES, YES we can! Check out the progression of photos; 2nd, 3rd and Platinum Series from left to right. (The 1st Gen not pictured, It was a 48 LED version utilizing our standard 1210 diodes)

Check out our latest pictures of the Formula Drift V-LEDS Dodge Viper! They will not disappoint!

Click on the picture for more photos from this event

The 2011 season got off to a rough start to say the least. Team SHR struggled with major engine failures on both cars. Sam Hubinette and the Dodge Motorsports Dodge Challenger was unable to make a qualifying run at Long Beach, forcing the “Crazy Swede” to miss the tandem drift elimination battles on Saturday.

Our own Dean Kearney, qualified for the show at Long Beach in his Mopar-powered SHR V-LEDS Dodge Viper SRT10. Kearney qualified No. 28 and fell in the opening round to Rhys Millen. Our amazing gallery documents moment by moment of the weekend shot by Tram Tran.